Introduction
Imagine nearly doubling your two-car garage without the cost of building a slab-on-grade structure. This garden shed lets you do just that to achieve 320 square feet of storage or livable space. As designed, the garden shed will add appeal to your yard, with its window and door shutters, along with the louvered vents in the side walls. The basic plan for this shed will allow you to run pipes and wires into the wall, add a bathroom and even a small kitchen. The roof will support a solar array to supply power. There's plenty of room indoors for battery storage for nighttime use or those cloudy days.
The shed is built to last. It's made from treated wood. Roofing paper and shingles protect the garden shed from any water damage stemming from precipitation. A gutter system attached to the fascia keeps the front entry ramp and foundation dry.
Materials you’ll need
|
|
Step 1 – Foundation Preparation
1.1 Clear the area where you want to build the shed and layout for the foundation. Use the below illustration as a guide.
1.2 For the foundation, dig the trenches at least 1 feet wide and 1 feet deep.
1.3 Fill the trenches to ground level with concrete and let cure, or harden. Since curing times vary between brands, read the packaging for recommended curing times.
1.4 Once the concrete has cured, use standard-sized bricks and lay them across the foundation. You will need roughly 285 bricks for this step.
Step 2 – Framing The Floor
2.1 Assemble the frame using 1 1/2″ x 7 1/4″ pressure-treated lumber. You will need fifteen boards cut to 15′-9″ that will be the joist.
2.2 Secure the beams with 8×5″ wood screws.
2.3 Using a speed square or carpenter’s square, check the corners to make sure they are 90°.
Step 3 – Assemble Front Wall Frame
3.1 Using 1 1/2″ x 3 1/2″ and 3 1/2″ x 3 1/2″ pressure-treated lumber, construct front wall frame using the drawing below as a reference. You will need three boards cut to 11″ that will be the cripple studs, one board cut to 5′-4″ that will be the door header, sixteen boards cut to 6′-11″ that will be the studs, two boards cut to 7′-4″ that will be the bottom plates and one board cut to 20′ that will be the top plate.
3.2 Connect the beams with 2×4″ wood screws.
3.3 Using a speed square or carpenter’s square, check the corners to make sure they are 90°.
Step 4 – Assemble Back Wall Frame
4.1 Using 1 1/2″ x 3 1/2″ and 3 1/2″ x 3 1/2″ pressure-treated lumber, construct back wall frame using the drawing below as a reference. You will need seventeen boards cut to 6′-11″ that will be the studs and two boards cut to 20′ that will be the top and bottom plates.
4.2 Connect the beams with 2×4″ wood screws.
4.3 Using a speed square or carpenter’s square, check the corners to make sure they are 90°.
Step 5 – Assemble Side Walls Frames
5.1 Using 1 1/2″ x 3 1/2″ pressure-treated lumber, construct side wall frames using the drawing below as a reference. You will need four boards cut to 5 1/2″ that will be the cripple studs, four boards cut to 2′-10 1/2″ that will be the studs, two boards cut to 3′-4″ that will be the window header and rough sill, twelve boards cut to 6′-11″ that will be the studs and two boards cut to 15′-5″ that will be the top and bottom plates.
5.2 Connect the beams with 2×4″ wood screws.
5.3 Using a speed square or carpenter’s square, check the corners to make sure they are 90°.
Step 6 – Assemble the Roof Frame
6.1 Using 1 1/2″ x 5 1/2″ pressure-treated lumber, cut thirty-four rafters 9′-5 1/2″ long according to the dimensions.
6.2 Using 1 1/2″ x 3 1/2″ pressure-treated lumber, cut fifteen collar ties 7′-2 1/4″ long according to the dimensions.
6.3 Using 3/4″ x 7 1/4″ pressure-treated board, cut the ridge board 20′ long according to the illustration below.
6.4 Connect the beams with 2×3″ wood screws.
Step 7 – Install Shed Doors
7.1 Build the door frames for the shed using 1 1/2″ x 3 1/2″ pressure-treated lumber and secure with 5″ wood screws. You will need two boards cut to 5′-11 3/4″ that will be the vertical girts and two boards cut to 2′-3/4″ that will be the horizontal girts.
7.2 Prepare the 9/16″ plywood sheet with dimensions 2′-7 3/4″ x 5′-11 3/4″ for the doors according to the drawing.
7.3 Use 2 1/2″ x 3/4″ pressure-treated lumber for the door trim and fasten with 2″ wood screws. You will need two boards cut to 2′-2 3/4″ and two boards cut to 5′-11 3/4″.
7.4 Using 1/4″ x 3/4″ pressure-treated lumber, cut and install a starter course 2′-2 3/4″ long.
7.5 For the exterior siding on the door, use 1/2″ x 6″ wood siding boards and the illustration below as a reference.
7.6 Assemble siding shields with 2″ galvanized nails.
7.7 Install three 3″ door hinges using 6×1″ wood screws. Finish the installation of the doors by attaching 4″ surface bolts and 6″ door pulls.
Step 8 – Roof Sheathing Installation
8.1 You will need 400 Sq Ft of asphalt shingle roofing.
8.2 Add the metal drip edge to the fascias.
8.3 Cover the plywood with building paper.
8.4 Install asphalt shingle roofing using an industrial stapler.
Step 9 – Window Installation for Side Walls
It is necessary to prepare 2 windows.
9.1 Using 1 1/2″ x 2 1/2″ pressure-treated lumber, assemble the outer frame for the window as shown in the drawing below. You will need two boards cut to 3′-1″ that will be the vertical girts and two boards cut to 3′-4″ that will be the horizontal girts. Additionally, add vertical 2′-11 1/2″ long and horizontal 3′-1″ long supports using 3/4″ x 1″ lumber and cut the recesses for the window hinges.
9.2 Use 1 1/2″ x 1 1/2″ pressure-treated material to make the inner frame and secure with 3″ wood screws. You will need two boards cut to 2′-9 3/4″ that will be the vertical girts and two boards cut to 3′-3/4″ that will be the horizontal girts. Mill a recess for the glass panes and for the hinges.
9.3 Use 1 1/4″ x 1 1/2″ pressure-treated material to make the inner frame supports and secure with 3″ wood screws. You will need two boards cut to 2′-9 3/4″ and mill a recess for interconnection.
9.4 Prepare and install glass into inner frame groove and fasten it by window beading from four sides. Use 1/2″ galvanized nails.
9.5 Install two hinges (3″) with 6×1″ wood screws and assemble the window. Install a lock on the inner side of the window.
Step 10 – Assemble and Install Window Shutters
It is necessary to prepare 4 windows shutters.
10.1 Assemble frames using 3/4″ x 1 1/2″ pressure-treated lumber and secure with 3″ wood screws. You will need one board cut to 1′-4 3/4″ two boards cut to 3′-3/4″ that will be the vertical girts and two boards cut to 1′-7 3/4″ that will be the horizontal girts.
10.2 Mill a recess along the vertical girts for the jalousies.
10.3 Use 1/4″ x 1 1/2″ pressure-treated lumber for the jalousies. You will need twenty-two boards cut to 1′-5 3/4″.
10.4 Install two 3″ door hinges using 6×1″ wood screws.
Step 11 – Assemble Decorative Door Shutter
It is necessary to prepare two decorative door shutter.
11.1 Assemble front frame using 1 1/2″ x 1 1/2″ pressure-treated lumber and secure with 3″ wood screws. You will need two boards cut to 6′-7″ that will be the vertical girts and two boards cut to 1′-5 1/2″ that will be the horizontal girts.
11.2 Assemble back frame using 3/4″ x 2 1/2″ pressure-treated lumber and secure with 5″ wood screws. You will need two boards cut to 6′-7″ that will be the vertical girts and two boards cut to 1′-3 1/2″ that will be the horizontal girts.
11.3 Use 3/4″ x 3/4″ pressure-treated lumber for the lattice. You will need thirty-six boards cut to 2′-3/4″. Assemble according to the drawing.
Step 12 – Install Roof Drainage System
12.1 Assemble roof drainage system on the front fascia board. You will need 5″ half round gutter 18′ long, two end pieces with the outlet, six 45° elbows, two 3″ pipes
6′ long, two joint connectors and two end caps.
12.2 Fasten the round gutter to the fascia with the round fits of hunger.
12.3 Fasten the vertical pipe section with the four wall fasteners.
Step 13 – Assemble and Install Door Ramp
13.1 Assemble five door ramp frames from pressure-treated lumber and secure with 3 and 5″ wood screws. For each frame you will need one 1 1/2″ x 1 1/2″ board cut to 1′-8″; one 1 1/2″ x 2 1/2″ board cut to 3′-3/4″ and one 1 1/2″ x 3 1/2″ board cut to 6 1/4″.
13.2 Connect and secure all frames using one 1 1/2″ x 2 1/2″ board 5′-9″ long and 3″ wood screws.
13.3 Cut the 9/16″ plywood sheet with dimensions 3′-3/4″ x 5′-9″ for the top plane and two sheets with dimensions 9 1/4″ x 2′-9 1/2″ for the sides.
13.4 Assemble siding shields with 2″ galvanized nails.
Step 14 – Decorate the Shed
Now that you’ve finished the shed, you are ready to paint it or finish with a wood stain or preservative.
Download Printable PDF Straight To Your Inbox!
Enter your details below and download the extended version of this plan.

Write a Review
Leave a reply Cancel reply